P0345 infiniti g35




P0345 infiniti g35

Article Navigation:
  • Photo
  • P INFINITI G35 Camshaft Position Sensor Circuit Bank 2
  • Video
  • RELATED PAGES
  • Repair Information for P Infiniti G35 code. Learn what does P Infiniti G35 Camshaft Position Sensor Circuit Bank 2 means, location and.

    Oct 9, You have now completed the VQ35 Camshaft Position Sensor replacement for your Infiniti G35 as well as fixing your P OBDII error.

    P code definition The P code indicates that the car's computer has detected an incorrect voltage reading from the bank 2 camshaft position sensor.

    P0345 infiniti g35

    P0345 infiniti g35

    They send certified and screened mechanics straight to your door and enable you to save big on car repair and maintenance. One other thing I will point out is that many members have gone with aftermarket sensors from Autozone, Orilley's, etc. If one is weak, they are likely all weak. Find all posts by nicker.

    P0345 infiniti g35

    P0345 infiniti g35

    P0345 infiniti g35

    P0345 infiniti g35

    P0345 infiniti g35

    P OBD-II Trouble Code: Camshaft Position Sensor A Circuit Malfunction (Bank 2)

    Find out the answer in here! Received 99 Likes on 12 Posts. Other years may be similar but I'm not sure. This is my way to remove your cam position sensors without doing a bunch of extra work. Bank 2 sensor Driver side: It's held in place by 4 hex bolts. Remove all 4 bolts and the throttle body will come right off.

    Just below it in green is the cam sensor. It was brought to my attention the sensor my not come off by simply pressing down on the green tab. If you run into this problem, try pushing on the sensor from the base and the tab may unlatch itself.

    P0345 infiniti g35

    If all else fails, remove the 10mm bolt, and pull the sensor out with the clip still attached to the sensor. The sensor may be difficult to remove from it's orifice. The O-ring that seals it my be making it difficult to remove. Just keep pulling and it will come out.

    See the diagram below to do this. Install all parts in reverse order as above. Bank 1 sensor Passenger side: This sensor can be removed without removing any parts. Unbolt the sensor and replace. See diagram below for testing instructions. Edit 1 April 25, Ok, so now you replaced your sensor s but your service engine soon light SES is still on. How do I get my light to turn off??? Repeat the following steps 2a and 2b procedures quickly five times within 5 seconds. Fully depress the accelerator pedal HARD.

    P0345 infiniti g35

    Fully release the accelerator pedal. Wait 7 seconds, fully depress the accelerator pedal and keep it for approx. Fully release the accelerator pedal while the CEL is still blinking 5. Wait about 10 seconds. Fully depress the accelerator pedal and keep it for more than 10 seconds. Fully release the accelerator pedal The CEL light will continue to blink. The CEL light should be gone.

    After you perform step 3, the CEL will start flashing. The series of flashes will actually display codes if any are present. Now take the car out for a drive. If the light comes back on in 5 or 10 miles, then your sensor replacement did not fix your problem. This could be due to a variety of things but is not limited to the following: Your connector may be loose. You replaced the wrong sensor this only applies if you only changed 1 of the 2 sensors 4.

    Your cam sensor was not the problem in the first place Hence, you changed out a good sensor without properly troubleshooting it and wasted your time and money. If you changed your sensor out and are still experiencing the exact same issues, re-check the engine code you are getting and troubleshoot according to the FSM. Be mindful that the CKP sensor is often linked to cam sensor error codes, and the CKP could also be contributing to your issues.

    P0345 infiniti g35

    Do all the testing possible, and then replace parts. Just because you are getting a cam sensor engine code, does not necessarily always mean the cam sensor is bad. Edit 2 April 25, I have been asked many times how to properly test the sensor. The following should answer most questions involving this: No matter what terminals you are testing, you are simply looking for any resistance reading.

    The resistance will vary according to many factors temperature, connection quality, sensor wear, your meter etc. All this test is really meant to check for is an open circuit within the sensor. If the sensor is reading open while you are correctly performing the test, then it is definitely bad. If your meter is reading anything but open, then your sensor is technically passing this test. This doesn't necessarily mean the sensor is positively good though. A very high resistance reading would also likely indicate a problem, but will not show as open on your meter.

    How to Replace Bad Camshaft Position Sensor in Your Car Code P0340 Infiniti G35 Nissan 350z Altima



    • Подписаться по RSSRSS
    • Поделиться VkontakteVkontakte
    • Поделиться на FacebookFacebook
    • Твитнуть!Twitter

    Leave a Reply

    Return to Top ▲TOP ▲